Setting up a Brick Paver Walkway or Face Bricks

The use of Bricks or Pavers to create a walkway or patio area matches a home in a method that is unequaled. In addition, installing a Brick or Paver walkway does not always require a pro.

The key to setting up a Brick or Paver Walkway is to first appropriately prepare the area where the bricks/pavers are to be set up. The location ought to be removed at least a foot down, removing all topsoil and clay soil. In addition, string lines need to be strung on each side of the walkway. The string lines show the finished height of the pathway.
Once the location has been dug down, 3/4" gravel stone must be laid in and tamped down tightly. The height between the tamped down sand and the stringline should equal the density of the brick or paver.

Now that you have a stable base, put a 1" pipeline or journal board the length of the walkway on either side of the sidewalk. Then using a flatedge, e.g. a 2"x4" board, slide it over the two lengths of the pipe/ledger board. In doing this you will create a level area to lay the bricks/pavers.

Now location on the level sand/stone dust strips of plastic brick borders. Set up a work on both sides of the prepared location. These strips will function as your sidewalk border and help to preserve the integrity and shape of the pathway. You can get these plastic strip borders at the majority of home enhancement shops. The strips need to be anchored down with 12" galvinized nails. You ought to sink these nails into the ground and through the strips every foot.

Once this is done, you can then begin to lay the bricks/pavers. There are lots of patterns you can lay. I especially like the Herring Bone pattern. The key to laying the bricks/pavers is to make sure that they interlock with each other. Constantly stagger adjacent rows of bricks by get more info 1/2 of a brick to interlock them. This will again help maintain the integrity of the walkway.

Undoubtedly bricks/pavers will need to be cut or split when building here the walkway. Unless you wish to buy or lease a pricey wetsaw, I would recommend acquiring a simple brick/paver splitter. It is basically a chisel with a large end that is the width of the bricks/pavers. To in fact cut/split the brick/paver, lay it in a bed of sand and place the chisel at a 75 degree angle over the spot where you wish to break the brick. Then using a hammer strike the butt end of the chisel securely. You might need to do this a number of times. You might likewise wish to flip the brick/paver over and strike the other side of the brick utilizing the hammer and chisle. Within one or two strikes the brick/paver need to break cleanly. If your walkway has curves you will need to buy/rent a wetsaw.

After setting up the bricks, develop the outside edges with additional sand, and then shovel in the topsoil and load down strongly.
Finally, spread stone dust over the brand-new sidewalk and sweep into the fractures. Repeat this procedure a number of times to guarantee the fractures are fully filled. This will finish the interlocking of the bricks and assist to get rid of any weed development. Just add yard seed to the outside edges and you need to have a beautiful entryway to your house within a number of weeks.


In addition, setting up a Brick or Paver pathway does not necessarily need a pro. The key to installing a Brick or Paver Walkway is to first effectively prepare the area where the bricks/pavers are to be set up. Now that you have a stable base, place a 1" pipe or journal board the length of the sidewalk on either side of the sidewalk. These strips will act as your walkway border and help to maintain the integrity and shape of the sidewalk. Undoubtedly bricks/pavers will need to be cut or split when constructing the sidewalk.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Setting up a Brick Paver Walkway or Face Bricks”

Leave a Reply

Gravatar